banner



How To Repair Tear In Leather Car Seat

To the left is a leather seat from an MR2, as can be seen, with years of utilise it has suffered significant damage to the left hand side The friction caused past rubbing against the leather has, over the years, resulted in a hole being made and a lot of abrasion to the surface. The below guide is intended to teach yous near leather machine seat repair, specifically showing you how to repair a hole in a leather car seat.


PRODUCTS REQUIRED

  • Leather Repair Kit - To Repair the hole. This kit also contains a small corporeality of colour, and then can be used on its ain to repair small areas of damage on a leather auto seat.
  • Small Leather Colourant Kit - Used to restore the leather colour to the whole bolster.

We also have a total selection of Leather Auto Seat Repair products on our website.

Leather Automobile Seat Repair Method


STEP ane. Prepare the leather car seat

The offset step information technology to prepare the leather for repair. Using the Leather Prep & abrasive pad, included in the Colourant Kit, gently rub the surface of the leather to remove whatsoever grease and oils that have accumulated.

This pace will besides remove whatsoever loose fibres and remove the manufactured terminate assuasive the colourant, applied later in this tutorial, to adhere to the leather properly.

Subsequently prepping, wipe the leather downward with the Alcohol Cleaner, this will remove any clay or dust from the expanse before moving on to the side by side step.


Footstep 2. Tidy the expanse

If you lot expect at the hole y'all tin can encounter that the leather is sticking outwards, like a lip. This lip will compromise the quality of the repair and it should be removed.

Using the scalpel or a scissors, carefully remove the lip by cutting it abroad at the base, taking intendance non to damage the surrounding leather.


STEP three. Apply the backing patch

In order to provide a firm bankroll for the repair, the leather repair sub-patch should exist applied. Accept the patch supplied in the kit and cut it to size, it should be plenty to completely encompass the repair with an additional 1cm of fabric surrounding the hole.

Once this is washed use the tweezers to insert one side of the patch underneath the leather so that the 1cm backlog is completely under the leather. Apply pressure to agree this in place and gently feed the patch under the remaining edges of the pigsty. When done the patch should lie flat under the repair, and the 1cm surrounding material nosotros left should be underneath the leather on all sides.

When this is done, put a small corporeality of Leather Glue onto the spatula supplied and feed this underneath the edges of the hole to coat the underside of the leather surrounding information technology, taking intendance not to motion the canvas patch. When all edges have been glued, apply force per unit area to bond the leather to the patch and allow to dry.


STEP 4. Fill the hole

At present that the backing patch is firmly in place, the hole in the leather must be filled. In order to exercise this; take a pocket-size amount of the Heavy Filler using the finish of the palette knife and place a thin layer into the hole over the bankroll patch. Make sure all the layer is very thin, merely roofing the sub-patch and let xx minutes to dry, this can be speeded upward by using a pilus dryer.

Proceed applying the heavy filler in sparse layers, it is crucial to use thin layers as the filler shrinks equally it dries and may not cure properly if the layers practical are besides thick. As a full general dominion, at least 5-6 thin layers should exist used to build up the filler until the filler level is built up to just below the height of the hole.

To remove backlog, with the application of each layer, smooth the area over with the sharper edge of the palette knife before drying the layer applied.


Pace v. More Layers of Filler

This is an illustration of what the pigsty will look similar after five or 6 layers of filler have been used.
It will not be polish but it will have most filled the hole completely.


STEP six. Add the terminal layer of filler

Use the concluding layer of filler to the hole, completely filling it and so that it is on an fifty-fifty level with the surrounding leather on the seat. Take intendance to let this final layer cure properly as when cured the filler can compress, reducing it to beneath the desired level.

Add together more repair filler if necessary.
If yous rub over the hole and filler gets onto the leather, remove it with the palette knife.

Your aim is to make full the hole so that it is level with the leather and not over filled. If you do over fill it, you tin can reduce it with sandpaper.

When you are happy with the level of the filler, and yous can no longer experience whatever 'ridge' between the level of the filler and the surrounding leather, clean the area with the Alcohol cleaner once again to remove any unwanted filler and dust from the surrounding expanse.


STEP 7. Apply an initial coat of colourant

The colourant supplied with the kit should have been matched to the colour of the leather item beingness repaired, unless you are completely re-colouring it.

Have one of the sponges supplied in the kit and utilise a small amount of colourant to it, then rub this into the area of the repair thoroughly. This allows the colourant to penetrate into the creases of the leather and valleys of the grain, giving a better overall cease.

When this is done, move onto the next step, where the colourant is sprayed on.


Stride viii. Cease the job

Using an airbrush spray as many thin coats of color over the leather car seat to thoroughly blend in the repair. For the best result, ensure that each coat is very thin and is given sufficient time to cure before applying the next. This will enable an fifty-fifty cease to exist congenital up and will avoid problems with uncured colourant. Information technology is not uncommon for the best repairs to apply x-xv thin coats of colourant, depending on the extent of the damage and the color used.

Once you are happy that the repair is concealed, the colourant is cured properly and it is well blended with the surrounding leather, the finish tin can exist applied. Using the spray gun apply 4 or 5  thin coats of the end, again allowing time for it to dry between each coat. The end seals the colourant in the leather preventing it from wearing and prolongs the leathers life.
When complete, allow 24 hours before using the item, to ensure the filler, colourant and finish have cured sufficiently.

In improver to the Leather Repair Kit, the Modest Leather Colourant Kit was used to colour this job as the area being repaired was quite large and required spraying.


Before
After

Source: https://www.furnitureclinic.co.uk/e-learning/how-to-fix-a-hole-in-a-leather-car-seat/

0 Response to "How To Repair Tear In Leather Car Seat"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel